• Marktleider in 3D Printing
  • Hoogwaardige service en support
  • Fysieke showrooms

Ultimaker Nylon Filament

Nylon (polyamide) is widely used by manufacturers to 3D print strong end-use parts and functional prototypes that require durability and abrasion resistance.
Lees meer
Sorteren op:
Incl. BTW | Excl. Verzendkosten Excl. BTW | Excl. Verzendkosten

How to print with Ultimaker Nylon

Nylon (polyamide) is widely used by manufacturers to 3D print strong end-use parts and functional prototypes that require durability and abrasion resistance. Ultimaker Nylon is designed to be more reliable and easier to print with than other nylon filaments on the market and features low moisture absorption and good adhesion to the build plate.

Besides single-extrusion prints, Ultimaker Nylon can be printed in combination with PVA and Breakaway on the Ultimaker S5 and Ultimaker 3. Printing Nylon in combination with TPU 95A or another color of Nylon can be done experimentally.

Always use the latest version of Ultimaker Cura and make sure that your printer is updated with the latest firmware version to include the correct material profile for Nylon.

Note: The information provided here applies to Ultimaker Nylon, similar quality cannot be assured with third-party filaments.

Recommended settings


Ultimaker Nylon is printed at a build plate temperature of 60 °C. The nozzle temperature differs per printer and nozzle size. For the best print results, we advise using the following temperatures:

Nylon settings

Note: On the Ultimaker S5 and Ultimaker 3, the nozzle and build plate temperatures on the first layer may be different due to the 'Print Temperature Initial Layer' and 'Build Plate Temperature Initial Layer' settings in Ultimaker Cura.

The temperatures listed in the table are used for the Ultimaker Nylon print profiles in Ultimaker Cura. For best results, it is crucial to always select the right printer, nozzle diameter, and material in Ultimaker Cura. Also, make sure you have selected the correct material on your Ultimaker 3D printer.


Nylon requires some cooling and therefore the fan speed is set to 35 - 40 % in the Ultimaker Cura profiles. This ensures optimal form retention and helps avoid problems with layer bonding. For shorter layers with more detail, the print cooling fan speed will gradually increase to 100 %.


Ultimaker Nylon adheres well to the build plate, but for optimal adhesion and build plate protection, it is recommended to use a thin layer of glue.


For good build plate adhesion, apply a thin layer of glue (included in the accessory box of your 3D printer) to the glass plate. Not using the glue results in a risk of chipping the glass plate when removing the print.

The adhesion sheets of the Advanced 3D Printing Kit can be used for even better adhesion.

Ultimaker Cura build plate adhesion

The Ultimaker Cura profiles for Ultimaker Nylon have been optimized to print with either a brim or a raft, depending on the selected printer. In the Ultimaker S5 and Ultimaker 3 profiles, a brim is selected by default, while the Ultimaker 2+ profiles use a raft as platform adhesion type. This raft is especially recommended for large models, while for smaller models a brim should be sufficient.

When using a raft, it is recommended to remove it when the build plate is still warm. This will make removal of the raft easier.

For more tips on how to improve the build plate adhesion, see this page.

Printing conditions

Ultimaker Nylon is not prone to warp or delaminate and does not need additional accessories to create a good printing environment. Optionally, the front enclosure of the Advanced 3D Printing Kit can be used to get more consistent and reliable 3D prints on the Ultimaker 3 and Ultimaker 2+.

Health and safety

Ultimaker Nylon is safe to print when using the recommended temperature settings listed above. To ensure a comfortable and healthy environment we recommend 3D printing in a well-ventilated area.

For more information, download the safety data sheet for Ultimaker Nylon here.

Wij slaan cookies op om onze website te verbeteren. Is dat akkoord? Ja Nee Meer over cookies »